How To Replace A Bathtub On The Second Floor

February 14, 2021

Consult the manufacturers literature and measure to make sure the drain is in the correct location. Walk-in tubs are designed for comfort and flexibility.

How To Install A New Bathtub For Dummies Bathtub Plumbing Diy Plumbing Easy Bathroom Organization

Remove the subfloor section to eliminate all soft rotting wood.

How to replace a bathtub on the second floor. Then put another large bead of silicone on the underside of the drain flange and then screw in the drain to the threaded elbow. If the gaskets or putty break down the tub drain may leak into the space below the bathtub. See below for a shopping l.

Use a specialty drain removal tool inserted into the. As for tracing the pipes - if theyre copper you might be able to use a metal detector but its generally most reliable to open the walls up and trace them. Both add years of life to an existing tub at a fraction of the cost of full-scale replacement and in a fraction of the time.

Soaking tabs hold more water and are suited for longer baths. Make sure to get all of the damaged or moldy. They are larger and more comfortable coming at a cost of 1500 to 10000.

Checkout my video on installing the Tile. Remove any stringer supports left on the wall. Now that the drain assembly is in place apply silicone to the both sides of each drain gasket.

This Old House plumbing and heating expert Richard Trethewey shows how to replace an old bathtub drum trap with a new PVC P-trap. Remove the screw in the center of the strainer cap in the bottom of the tub with a flat-head screwdriver. You can also choose to install a soaking bathtub at a cost of anywhere between 250 to 12000.

Dont press too hard. Bathtub liners and bathtub refinishing. One person should lift the front edge of the tub while another slides a couple of 1 x 4 boards underneath to get it off the floor.

Check the drain and replace any damaged parts. Bathtub drains are sealed in place with rubber gasket beneath the tub with another gasket or plumbers putty used to seal the top of the drain flange where it fits against the inside of the drain opening. Then after the contractor uses fans and forced-air flex ducting into the subfloor to dry out the subfloor area and the top surface of the drywall remediation is completed by painting the affected areas with Kilz or similar mildewcide and stain-blocking paint followed by repainting usually the entire affected wall s and ceiling s to get a match with finish paint in the desired color.

To replace a bathtub first youll need to cut a hole in the wall behind your tub and turn off the water supply to your bathroom. Preparation It is important to find out all the rules and regulations regarding bathroom plumbing before getting to work. Screw ledger boards to the studs at the height recommended by the manufacturer.

Allow rotted areas to dry out then apply a coat of wood preservative to. Repairing or replacing the bathtub drain fitting. Slide the tub out of the alcove using the 1 x 4 boards as skids.

Then remove the tub spouts drains and drain shoe and. The decision is based on faucet placement and which side of the. Youll be opening up the wall on the other side of the tub or the floor under the tub or more likely both.

Use Bathtub Liners or Refinishing to Revitalize Your Tub But two better options are available to price-conscious homeowners with tubs in need of a face-lift. Cut the old bathtub caulking loose from the joint by running the edge of a razor scraper along both sides of the joint. Bathtubs without enclosures come with either left-end aprons or right-end aprons.

This basic guide has a few of the steps that need to be taken to install bathroom plumbing on the second floor of your home. Purchase a waste-and-overflow unit 33 The Home Depot and determine how you will connect it to the drain line. Then slowly lower the bathtub into place being careful not to smear the silicone sealant.

Pull nails before cutting along joists. When you replace the subfloor the new ends have to sit on the joists so cut out your wet subfloor along two joists on either side of the damage. Use a jigsaw to cut out the circles as shown in Photos 9 10 and 11 to make the floor fit under the flange.

Upstairs Shower Install Help