How To Replace A Bathtub And Surround
Keep an eye out for wires and pipes. When you pull the drywall off the fiberglass surround will come with it.
How To Install A Bath Tub Surround Installing Bathtub Bathtub Surround Tub Surround
Learn how to replace a bathtub faucet with our helpful guide.
How to replace a bathtub and surround. A new tub installation will take around 6-9 hours and will cost you between 540 and 1620 in labor. Most plumbers charge by the hour at a cost of between 45 to 65 per hour. Step 6 Lay the carton template on top of the.
To replace a bathtub first youll need to cut a hole in the wall behind your tub and turn off the water supply to your bathroom. It can be necessary to move andor replace the plumbing pipes to fit the new tub. Most mount directly to bare studs with screws nails or manufacturer-provided clips although a few can be glued to a clean smooth surface.
Plumbing labor costs lie anywhere between 500 to 1600 depending on the scope of work. Add about 200 for a matching tub. This means you will have to remove the drywall around the tub surround so the lip of the surround panels can be screwed right into the studs.
And cut a hole in a wall to get the old tub out and the new one in. The notch helps to remove the panel from around. With this type of tub surround drywall or trim pieces will likely have to be added over the lip to cover it up.
Use your power drill to remove the drywall screws. A 3-by-3 inch tile is 9 square inches. Use your nail bar to remove drywall nails from the wall studs.
Remove the studs from the panels and then cut the caulk. Using a shovel scoop up the rubble and put it into a garbage can. Use a bi-metal bladefor this and itll be a breeze.
Pull the drywall and tub surround from the studs. Using the tubshower surround carton for a template mark holes where the showerhead faucet handles or spout will protrude through the wall. Apply caulk on the panel in a zigzag pattern then apply a bead on the wall spreading it evenly with a trowel.
Finally once all the big stuff has been. And then proceed with the panel removal. Cut the tub surround with a jigsaw or handsaw.
To create a more solid base you want to install the side panels first by lining them up with your tub. Press firmly releasing only after a good 1-2 minutes then applying a line of adhesive at the base before the bathtub. Start at the top of the corners and go down to the tub deck.
Most new tubs will take anywhere between six to nine hours to install with an additional three hours to remove an existing tub5 Mar 2018. Its less expensive to refinish the bathtub 300-600 or install a bathtub liner 500-4000 but a replacement can mean you get precisely the tub you want. Cut through the plastic with smooth fluid movements.
One person should lift the front edge of the tub while another slides a couple of 1 x 4 boards underneath to get it off the floor. Depending on the nature of your project you may choose to hire a licensed plumber 45-65 per hour or a handyman 60-90 per hour to install your bathtub. Dont use coarse-toothed saws.
Be sure that the knife goes through to the supporting wall that is behind the tub surround but do not damage it. Slide the tub out of the alcove using the 1 x 4 boards as skids. Hold the reciprocating saw at a shallow angle to avoid wiring that might be in the walls.
Pull off the drywall with a hammer and pry bar working from the edges. Divide the area of the wall 2592 square inches by the area of an individual tile 9 square inches giving you the number of tiles required for that surface 288 tiles needed for the sample wall. Most likely youll need to remove the nails or screws that hold the drywall to the wall studs.
Repair carpentry drywall and tile. They can chip the plastic tub surround. A plastic garbage bag will probably just tear open so put the old tile directly into the garbage can.
Remove any stringer supports left on the wall. Take a pry bar and wedge it under the bottom edge of the tub surround. TheHomeDepot HomeImprovement DIYSUBSCRIBE to The Home Depot.
Cut a notch out of the top of the tub surround down to the shower arm with the utility knife. Use a dustpan and scoop to get the smaller pieces and shards. Measure the size of the tiles you want to use.
Composite tub surrounds and tubs are the strongest and have the longest projected life span. Thicker sturdier tub surround panels are usually attached direct-to-studs. Start the saw blade in one of the holes you made.
Using a utility knife slice through all the caulk at the edges and in between the panels. Take a reciprocating sawand cut the tub surround at the corners. To remove a tub surround and replace it with tile start drawing lines from where you want to cut.
Use a utility knife with a sharp blade and score several times until the blade slices completely through. Start cutting with the lines and remove the nailing flanges. Then remove the tub spouts drains and drain shoe and.
Before After Replacing My Fiberglass Bathtub Bathtub Remodel Bathtub Walls Bathtub Wall Surround
How To Install A Bath Tub Surround Bathtub Wall Surround Bathtub Surround Shower Surround Kits
Install A Tub Surround Or Shower Surround Shower Surround Shower Stall Bathtub Surround
Install An Acrylic Tub And Tub Surround Acrylic Tub Shower Remodel Diy Bathroom Repair
